Some are called chill rolls, some are called heating rolls. In most cases, these engineered rolls all serve a similar purpose – to transfer heat energy onto or away from a web.
Heat transfer rolls are common in many converting processes today. As engineered film and specialty substrates become more prevalent, the use of these engineered rolls has increased even more. Yet, the physics of heat transfer rolls are often misunderstood. This can result in incorrect roll specifications and improper use that can directly affect web quality.
Though one doesn’t have to be an engineer to properly specify and use heat transfer rolls, a little of the right knowledge can go a long way in maintaining the ideal process parameters. The following seven heat transfer topics are common misconceptions we routinely encounter. Let’s clear up these issues now and you’ll be well on your way to becoming a heat transfer myth buster.
Myth 1: All heat transfer rolls are pretty much the same.
It’s not right to say all car engines are pretty much the same. Different materials and engineering makes a significant difference in product life and performance. The same is true for heat transfer rolls. With converters trying to maximize performance of their equipment, most applications require some serious engineering to optimize heat transfer.
Designing the right roll starts with the right operating data. Field data is best, but when not available, a computer model or heat transfer simulation must be used to model the application. The engineer can use this data to design the roller with the correct internal fluid path, optimizing turbulence and maximizing heat transfer performance.
The physical performance of the roller must also be considered. Roll body deflection and journal stress are among the most important details when engineering a roll for a specific application. Particular design techniques and special materials can be used to reduce or manage challenges with design details, such as deflection and stress. In some cases, an FEA (Finite Element Analysis) is required to determine the best materials and structure for the heat transfer roller.
Myth 2: Rotational direction must be matched with flow direction.
Some customers still want “inlet,” “outlet” and “directional rotation” stamped on the outside of their straight-pitch heat transfer rolls and that is okay. In reality, it really doesn’t matter which is which. Only on a variable pitch or “gain-pitch” roll does fluid need to be introduced at a specific end of the roll.
Myth 3: Roller temperature can be controlled by the flow rate.
Heat transfer rolls are designed to achieve a certain fluid velocity and turbulence in order to produce a transfer of energy, all while maintaining a desired Delta T (symbolized as ΔT, this is the difference
in temperature of the fluid entering vs. leaving the roll, or the temperature gradient across the roll face).
When fluid flow is increased, the dynamics of heat exchange within the roll, along with ΔT, change. When energy is transferred into or away from a fluid, the flow rate of that fluid must be adequate to support the rate of heat transfer taking place. If the flow rate is inadequate, the result will be a large ΔT.
the fluid flow rate must be to maintain consistent temperature across the face of the roll.
Example: Over time, the heat load was increased on a 48 inch diameter hot oil roll designed to bond two webs. The roll was originally designed at a specific flow rate that was no longer adequate to
support the process. To compensate for the increased heat load, the operators increased the oil temperature; but the roll design restricted the fluid flow rate. The result was oil temperature at 380° F coming in and 340° F exiting (a 40 degree ΔT). The web was getting “burnt” on the entry side of the roll and not bonding on the exit end. The solution was in the design of new rolls with larger journals that could accept a much higher flow rate to get ΔT to less than 10° F.
ΔT is controlled by flow – and that is almost exclusively determined by the design of the roll. By design, ΔTs can be achieved as low as 1° F. The appropriate ΔT for any application is dictated by the criticality of the process. Fluid temperature will control roll temperature but flow rate is ultimately the driver to uniform ΔT.
Myth 4: The supplier will know what surface finish I need for my process.
Specifying the proper Ra is critical in achieving the desired web finish. Clear web finishes require roll finishes at the lower Ra range. Not every converter needs a perfectly clear web – nor the cost associated with a fine mirror finish roll. If the needed Ra spec is unknown, a good roll provider can often help by either examining a sample of the finished product, or the existing roll. Examining an existing roll is preferred.
Process knowledge and experience is key to determining the proper finish on a roller; but many times, assistance can be provided over the phone by an experienced roll provider who understands coatings and finishes. Specific and measurable values must be used to specify a roll surface finish. Avoid using ambiguous terms such as “mirror” or “matte” that mean something different to everyone who encounters them.
Myth 5: A double-wall heat transfer roll is always the correct choice.
Whenever the goal is to control web temperature, a double-wall spiral heat transfer roll is imperative. Sometimes the goal is simply to maintain a general temperature of a specific roll. Then, a single-wall heat transfer roll becomes the most cost-effective solution.
Examples: A rubber-covered nip roll opposing a heated roll – the bond between the rubber covering and the roll core might be at risk if the nip roll gets too hot. A single-wall, rubber-covered heat transfer roll easily maintains an acceptable nip roll temperature. In a different application, heated single-wall rolls are used to keep an adhesive coating warm during a coating operation.
Myth 6: Any water will work in a heat transfer roll.
Water chemistry varies throughout the country and it’s a known fact that water acidity, scale and hardness can affect the life and performance of a heat transfer roll.
Some customers run city water, ground water or even river water through their heat transfer rollers. Untreated water can contain all sorts of unwanted minerals and a chemistry that causes excessive rust and other deposits to build up in the flow passages of a heat transfer roll.
A closed-loop system that uses conditioned and treated water is the ideal way to ensure the life and performance of a heat transfer roll. It’s not much different than the coolant system in your car. Properly maintained with the correct fluid chemistry, the system will operate trouble free for years.
Myth 7: Bigger is always better.
It is true that heat transfer is all about dwell time (web on roll). It is also true that a larger roll will give you a longer contact surface and therefore more dwell time. Yet, there are other factors in play.
A boundary layer is a component in the system inhibiting or slowing heat transfer. In this case, the principle boundary layer is air trapped between the web and the roll. This boundary layer is a function of web speed, web tension and roll diameter. As the roll diameter increases, so does the boundary layer, diminishing heat transfer. In addition, the use of smaller, multiple rollers can be configured to contact both sides of the web. This can be a real advantage with thicker webs. Finally, the cost of two smaller rollers may be less than the cost of one larger roller.
The transfer of energy is critical to many processes in web converting. Effective, predictable and efficient heat transfer is paramount to process performance – and understanding these processes is the key to success. Like many products, a heat transfer roll is engineered for optimum performance based on specific operating parameters. It is important to remember that flow rate and ΔT are inverse proportions. With all other things remaining the same, if a ΔT of 10 needs to be 5, the flow rate has to double. Going from 2° F to 1° F doesn’t sound like much, but it is still double.
There are various roll designs available to achieve any desired energy transfer rate, including gain pitch spiral designs with varying flow velocities and temperature differentials. Look to a qualified roll producer with certified engineering in-house to provide the necessary roll design.
Web temperatures can be measured today using a relatively inexpensive hand-held pyrometer. When temperatures are not what they should be, don’t touch that dial. Call a heat transfer roll specialist to review the facts and get some expert advice.
Pete Eggen, Application Engineering Manager at Webex, has more than 20 years experience within the converting industry in process analysis, product design, development and applications engineering for precision rolls, from Idler Rolls and Vacuum Rolls to Heat and Chill Rolls. Pete can be reached at +1 (920) 729-6666 or email@example.com.
Dave Grishaber, Technical Sales Lead at Webex, has more than 30 years experience helping companies implement precise temperature control using Heat Transfer Rolls. Dave can be reached at +1 (920) 729-6666 or firstname.lastname@example.org.